IFLIGHT Chimera7 6S LR w/ DJI Air Unit HD System - BNF
zoom_out_map
chevron_left chevron_right
Promo !-10%

IFLIGHT Chimera7 6S LR w/ DJI Air Unit HD System - BNF

IFLIGHT Chimera7 6S LR w/ DJI Air Unit HD System - BNF

 

Voici le dernier drone Freestyle long range HD de IFLIGHT, en dimension 7 pouces, assemblé avec soin avec les meilleurs composants et avec le DJI FPV Air Unit HD

  • TBS CROSSFIRE NANO RX (SE)
  • 1300KV
611,10 CHF TTC 679,00 CHF -10% 567,41 CHF (HT)
TTC
check En Stock

IFLIGHT Chimera7 6S LR w/ DJI Air Unit HD System - BNF

 

Introducing what has been requested for too long already! A super efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want!

Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above. 

GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included).

Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).

 

HIGHLIGHTS:

 

- 6mm rigid arm design for more stiffness

- Top- and bottom battery mount option

- XING 2806.5 efficient wide stator motors

- GPS pre-installed for more safety at distance

- GoPro TPU bottom stand (GoPro protector not included)

- 360° TPU protection, DJI cam protection and antenna mounts

- No props in view (DJI Air unit record in 1080p/60fps)

- Battery voltage LED status light (illuminated IF logo on the bottom)

 

PRE-TUNED & PRE-SETUP:

 

- Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF

- Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

- Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

- GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour.

Please check our linked article on "GPS Rescue Mode // Setup"

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

 

FRAME // :Chimera7

 

- Wheelbase: 320mm

- Main body dimension: 258*199mm

- Bottom to top distance: 20mm

- Arm thickness: 6mm

- Bottom plate thickness: 3mm

- Top plate thickness: 2mm

- Upper(middle) plate thickness: 3mm

- Camera plate thickness: 3mm (included TPU inserts)

 

ELECTRONICS // SucceX-D F7 V2.2 Stack (50A 4-in-1 ESC):

 

SucceX-D F7 V2.2 TwinG

 

MCU: STM32 F722

Gyro:MPU6000

Baro: DPS310 (Barometer can only be used with Betaflight 4.3.0 and above)

Blackbox:32MB

Betaflight OSD: YES

BEC: 5V 2.5A / 9V 2.5A

Current sensor scale:  100

Inverter for SBUS input (UART2-RX)

Smartaudio & Tramp VTX protocol supported

Beeper pad : Yes

RSSI input pad: No

UARTs:5

Motor outputs: 8

8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)

6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)

BLHeli32 Telemetry:RX5

Input voltage:recommended 2-6S, MAX 8S

Firmware target: IFLIGHT_F722_TWING

Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm

Dimensions:   36*36mm

Weight: 8.1g

USB type-C

 Product Link

 

ESC // SucceX 50A

 

MCU: STM32G071

Up to 48kHz PWM frequency

Capacitance: 470uF/50V

Current Sensor: Yes

Input: 2-6S LIPO

Constant: 50A / Burst: 60A

BlHeli32 telemetry: Yes

BEC: No

Supports up to Dshot600, Proshot, Oneshot, Multishot 

Target: iFlight_G071_4in1

Weight:14.3g

Mounting pattern: 30.5*30.5mm/Φ3mm

Dimensions: 43*39mm (including the power pads)

 

BNF // Parts list (Build)

 

Prebuilt and indoor tested Quadcopter

 

1x Chimera7 frame

1x GoPro TPU bottom stand incl. lock screw

1x DJI Air Unit HD Digital System HD FPV system

2x Albatross LHCP RP-SMA 5.8g 150mm antenna

2 sets x Gemfan tri-blade 7040 props (Set of 4 - Color may vary)

4x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)

 

Additional Suggested Parts (not included)

 

- Adjustable GoPro mount (0-40)

- 1300KV  Cruiser, suggested battery: 6S 4000mAh

L008905
2 kg
2 Produits
Vous aimerez aussi