IFLIGHT Chimera7 Pro 6S LR w/ DJI Air Unit HD System - BNF
zoom_out_map
chevron_left chevron_right

IFLIGHT Chimera7 Pro 6S LR w/ DJI Air Unit HD System - BNF

IFLIGHT Chimera7 Pro 6S LR w/ DJI Air Unit HD System - BNF

  • TBS CROSSFIRE NANO RX (SE)
  • 1300KV
749,00 CHF TTC 695,45 CHF (HT)
TTC
check En Stock

IFLIGHT Chimera7 Pro 6S LR w/ DJI Air Unit HD System - BNF

 

Introducing what has been requested for too long already! A super-efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want!

A super stiff frame for minimum resonance and XING2 2809 motors for maximum 7inch prop control.

Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising.

But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above. 

GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behavior; Setup instructions included).

Vertical and horizontal TBS Crossfire antenna mounts are included to cover you and your antenna dead-ends just in case.

GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).

 

HIGHLIGHTS:

 

- Battery voltage LED status light (illuminated IF logo on the bottom)

- 360° TPU protection, DJI cam protection and antenna mounts

- GoPro TPU bottom stand (GoPro protector not included)

- Lightweight Side Panels Design - Keep Your Rig Clean

- No props in view (DJI Air unit record in 1080p/60fps)

- XING2 2809 1250KV efficient wide stator motors

- GPS pre-installed for more safety at a distance

- 6mm rigid arm design for more stiffness

- Top- and bottom battery mount option

 

PRE-TUNED & PRE-SETUP:

 

- Is this your first BNF or are you just starting through with FPV?

- Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

- Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

- GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour.

Please check our linked article on "GPS Rescue Mode // Setup"

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

 

Specifications:

 

- Weight: 695g (without battery and GoPro mount)

- Total Dimensions: 258*200mm (body dimension)

- Upper(middle) Plate Thickness: 3mm

- Bottom to Top Distance: 20-29mm

- ESC // BLITZ E55 4-IN-1 2-6S ESC

- Bottom Plate Thickness: 3mm

- Camera Plate Thickness: 3mm

- Top Plate Thickness: 3mm

- Geometry:  DC (DeadCat) 

- HQ 7.5X3.7X3 Propellers

- Arm Thickness: 6mm

- XING2 2809 1250KV

- FC // BLITZ F722

 

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC):

 

BLITZ F722 Flight Controller

 

Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter

Smartaudio / IRC Tramp VTX protocol supported

Firmware target: IFLIGHT_BLITZ_F722

Motor outputs: 4x (SH1.0 connector)

Flash: 32MB (Blackbox flash)

I2C serial: SDA / SLA pads

Dimensions: 36.5*35 mm

Barometer: DPS310

OSD Chip: AT7456E

LED controller: Yes

MCU: STM32 F722

Beeper pad: Yes

Gyro: BMI270

Weight: 7.8g

UARTS: 6

 

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

 

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.

Mounting Holes: 30.5*30.5mm/Φ4mm

Target:   IFLIGHT_BLITZ_G2

Supports 2-6S Lipo input

Current sensor: Yes

Constant: 55 Amps 

Current rate: 200

Burst: 65 Amps

Weight: 15.3g

MCU: G071

BEC: No

 

Chimera7 Pro HD BNF Included Components and Parts

 

4 x HQ 7.5X3.7X3 CW propeller + 4 x  HQ 7.5X3.7X3 CCW (Color may vary)

2 x Albatross LHCP 5.8GHz SMA FPV Antenna

2 x iFlight Lipo Strap 20*250mm (Black)

1 x Pre-built and Tested Chimera7 Pro

1 x DJI FPV Air Unit Module + Camera

 

Note:

 

All iFlight BNFs are tested before shipment to guarantee the highest quality. 

If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.

iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support.

L012200
2 kg
2 Produits
Vous aimerez aussi