Skystars F7HD PRO4 FC & AM60 AM_32 60A 32Bit 3-6S 30.5mm 4in1 ESC Stack
zoom_out_map
chevron_left chevron_right

Skystars F7HD PRO4 FC & AM60 AM_32 60A 32Bit 3-6S 30.5mm 4in1 ESC Stack

New !!!  Latest Sykystars FC version HD Pro4 with MPU6000 Gyro

108,90 CHF TTC 100,74 CHF (HT)
TTC
check En Stock

Skystars F7HD PRO4 FC & KO60 60A 128K Blheli_32 3-6S ESC Stack

 

New !!!  Latest Sykystars FC version HD Pro4 with MPU6000 Gyro

 

1. Solder pads are the largest in size compared to other FC in market.

2. Proper solder pad spacing to avoid solder bridge and facilitate easy soldering. 

3. ESC connector on top-side rather than bottom which makes it easy for repair.

4. TVS Diode for Reverse Polarity Protection and Voltage Spike Suppression.

5. Powerful 3A BEC to supply all your electronics. 

6. Pads arrangement are executed in such a way that when you twist the wires of the camera VTX and RX you don't get any wire overlapping this gives you a uniform twist and clean look.

7. Support DJI O3 connector on the top side.

8. Support VTX ON/OFF Pit Switch.

9. Gyroscope independent power supply, No power lines near MPU6000 Gyro to avoid any EMI interference. 

10. Two stages of Quality check to reduce any faulty electronic. 

11. Comes ready with I2C support and INAV.

 

SKYSTARS F7HD Pro4 Flight controller:

 

MCU: STM32F722RET6 216MHz

Gyroscope: MPU6000 

Baro:Bmp280

OSD: Betaflight SPI OSD  DJI HD OSD(UART6)

Black box: 16MB

6x Uarts: UART 1/2/3/4/5/6

4x PWM outputs

1x I2C

3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)

USB Type-C(USB2.0)

1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr)

1x JST-SH1.0_6pin connector (10V/Gnd/TX6/RX6/Gnd/Sbus)

VTX 10V/Vbat filtered power ON/OFF Pit switch

DJI FPV OSD is supported by any spare UART

LED: 4 LED independent pads, support WS2812 programming lamp output.

Receiver: Support Sbus, crsf, ibus, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can actually be installed in any spare UART.

 

Power:

 

Input voltage: 3-6S

BEC: 5V/10V 3A max dual-channel BEC supports stable power supply on the sky side of DJI

LDO 3.3V: Max.250mA

 

FC Firmware:

 

BetaFlight firmware: SKYSTARSF722Pro

INAV firmware:SKYSTARSF722HD

 

Mounting:

 

Installation size: 30.5mm × 30.5mm The installation hole is M4 and supports shock column installation

External size 39mm × 39mm

Flight control weight: 6.9g

Flight control onboard voltage sensor

 

AM60 AM_32 60A 32Bit 3-6S 30.5mm 4in1 ESC:

 

Input voltage: 3-6S LiPo

Con.Current: 60A

Peak Current: 70A≥ 10S

Firmware: AM_32

Support: Dshot 600/1200

Mounting hole : 30.5X30.5 mm/M3

BEC: No

Product size: 41*46*7.6mm

Weight: 18g

 

Including:

 

1x F7HD Pro4 FC

1x AM60 AM_32 60A 32Bit 3-6S 30.5mm 4in1 ESC

8x Silicon grommets M4 to M3

2x JST-SH1.0_8pin cable, 4cm

1x JST-GH-6P cable for DJI port, 10cm

SKY-150749
0.20 kg
2 Produits