Skystars H7 STACK H743 DUAL BMI270 GYRO KM65A BLHELI32 F4 128KHZ 65A 4IN1 ESC - 30 X 30mm
Skystars H7 STACK H743 DUAL BMI270 GYRO KM65A BLHELI32 F4 128KHZ 65A 4IN1 ESC - 30 X 30mm
Skystars RC flagship H743 Dual Gyro Flight Controller with X8 support, OSD, dual BMI270 gyro, BMP280 barometer, 16M blackbox, 8 UARTS, and more.
The powerful MCU running at 480MHz should future-proof any new firmware updates coming in the next few years.
The KM65 ESC supports 3-6S battery power and current up to 65A, which makes it playfully handle motors of size 2207-2808.
The ESC has an aluminum heat sink on top to help dissipate heat better while protecting sensitive components from mechanical damage.
The ESC uses a powerful F4 32-bit processor and BlHeli_32 firmware.
Thus it supports telemetry, bidirectional DShot and PWM frequency up to 128KHz. The ESC is protected against voltage spikes by a TVS diode.
Features:
1. Solder pads are the largest in size compared to other FC in market.
2. Proper solder pad spacing to avoid solder bridge and facilitate easy soldering.
3. ESC connector on top-side rather than bottom which makes it easy for repair.
4. TVS Diode for Reverse Polarity Protection and Voltage Spike Suppression.
5. Powerful 3A BEC to supply all your electronics.
6. Pads arrangement are executed in such a way that when you twist the wires of the camera VTX and RX you don't get any wire overlapping this gives you a uniform twist and clean look.
7. Support DJI O3 connector on the top side.
8. Support VTX ON/OFF Pit Switch.
9. Gyroscope independent power supply, No power lines near MPU6000 Gyro to avoid any EMI interference.
10. Two stages of Quality check to reduce any faulty electronic.
11. Comes ready with I2C support and INAV.
SKYSTARS H743 DUAL BMI270 GYRO Flight controller:
MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash
Gyro: BMI270 dual
Baro: BMP280
OSD: AT7456E
Blackbox: 16M
8x Uarts (1,2,3,4,6,7,8) with built-in inversion.
8x PWM outputs
1x I2C
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
USB Type-C(USB2.0)
2x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr)
1x JST-SH1.0_6pin connector (R1/G/R6/T6/G/10V)
Dual Camera Inputs switch
VTX 10V/Vbat filtered power ON/OFF switch
DJI FPV OSD is supported by any spare UART
Vbat Input: 7~25V (2~6S LiPo)
BEC: 5V 2A Continuous (Max 3A)
LDO 3.3V: Max 250mA
Firmware: Betaflight - SKYSTARSH7HD
Mounting: 30.5 x 30.5mm
Dimensions: 39.5 x 39.5 x 7.8 mm
Weight: 10.1g
BL32-65A 4IN1 3-6S ESC BLHELI32 128K DSHOT1200 4-IN-1 ESC:
Support 128K Dshot1200, Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal
Excellent over-current capability.
Extreme stably support 6S LiPo battery with TVS.
Excellent heat dissipation performance
Better control performance F4 core MCU support 128K.
Input voltage: 3-6S LiPo
Con.Current: 65A
Peak Current: 90A≥ 10S
Firmware: BLHeli_32
Support : Dshot 600/1200
Mounting hole : 30.5mm/M3
BEC: No
Product size: 45.6*45*7.6mm
Weight: 19g
Includes:
1x Skystars H7 Dual BMI270 Gyro Flight controller
1x KM65 128K BL32 4IN1 ESC
8x Silicon grommets M4 to M3
2x JST-SH1.0_8pin cable, 4cm
1x JST-GH-6P cable for DJI port, 10cm
